Nowadays, the industry is formulated. No matter what form of machine equipment, fitness machines, furniture, etc.,There tend to be almost structural steel pipes and oil pipes pertaining to oil, gas, fluid infusion, and they occupy necessary position in fitness equipment. The large number associated with various tube types in addition to their complex forms have brought many difficulties to the processing of catheters.
: Safety precautions for esophagus bender operation
- Aluminum bending machine operating treatments
- Regularization of pipe bender
Safety precautions intended for tube bender operation
ONE PARTICULAR. When the machine program is started, be careful to never enter the swept range of the rotating arm.
2. If your machine tool is working, all personnel are prohibited from entering the area swept by the boom and also pipe bender fittings!
3. The hydraulic system with the roller bending machine instrument adopts YA-N32 ordinary hydraulic essential oil (formerly No. 20), which really should be replaced once a year under normal circumstances, and the oil filtration system must be cleaned at the same time.
4. When adjusting the slicer tool (mold), the adjuster have to press the button that will adjust. Never make adjustments by one person for the machine and the other around the control cabinet.
5. The core rod must be removed when adjusting the slicer tool or driving a good empty car.
6. The pressure on the hydraulic system should not be higher than 14 Mpa.
7. When manually adjusting the rate of the side drive cylinder, the rotating arm ought to be adjusted when it can be rotated to ≥900. The adjustment speed is synchronized using the linear speed of the side of the rotating elbow form. It is forbidden to push along side it pushing faster than the line of the edge of the rotating mold within the manual state. speed.
8-10. After using the general machine for a period of time, check the tightness of the chain to keep top of the and lower chains stretched.
9. During automatic operation while in the core bending mode, prior to a pipe bending arm profits, the operator must make sure that the core head is at the tube, or make sure that the core shaft isn't blocked when the bending arm returns, otherwise, the core head or core rod might be Bend or break.
15. After the work is passed, cut off the energy supply and do a good job of cleaning plus lubricating.
Steel bending machine operating procedures
1. The slicer tool must be properly grounded, and the wire shall not be not as much as 4mm2 copper soft line. It is not allowed to connect to a power supply voltage exceeding the specified range, plug-ins can not often be plugged in and from the plug when power is actually on, and the control circuit is not tested with a megohm meter, otherwise the device may be damaged.
TWO. When plugging and unplugging the connector, do not pull this wire or cable to counteract the welding from yanking off.
3. Proximity switches, encoders, etc. cannot often be hit by hard objects.
4. Do not click the display unit together with sharp objects..
5. The electrical box should be placed in a ventilated put, and it is forbidden to your workplace in dust and corrosive un wanted gas.
6. It is prohibited to install or transform the PC input along with output terminals without agreement.
7. When changing the energy supply of the unit tool, the motor rotation direction have to be reconfirmed.
8. The roller bending machine tool should be kept clean, and special attention really should be paid to that there must be no foreign matter in the sliding grooves such as clamping blocks and slipping blocks.
9. Lubricate the chain along with other sliding parts regularly.
12. The power must often be disconnected during cleaning and maintenance.
11. Preparation in advance of driving: Check whether the oil a higher standard the fuel tank gets to the oil level range, add oil to just about every lubrication point, turn within the machine to confirm the rotation on the motor, check the fat pump for abnormal audio, and check whether the hydraulic strategy is leaking after turning within the machine (the angle encoder just isn't allowed Come on);
10. Pressure adjustment: use electromagnetic overflow control device to adjust the pressure to make certain the system pressure reaches the desired working pressure, generally not beyond 12. 5 Mpa.
THIRTEEN. Mold adjustment: mold installation requires pattern and clamping block that they are centered, clamping block can be adjusted with bolts; the booster block is centered along with mold, booster block will be adjustable; core head is actually centered with mold, loosen main head frame Bolt, fasten the bolt after changing the center.
Regularization involving pipe bender
When coming up with and arranging pipe benders, steer clear of excessively large arcs, human judgements curves, compound bends and a lot more than 180. The arc. The excessively large arc not merely makes the tooling ungainly, but also is limited with the size of the tube bender: the design of human judgements curves and compound bending is rather unreasonable, which greatly stops mechanization and automated development, making it difficult for operators to eliminate heavy manual labor; A lot more than 180. The arc makes this steel bending machine unable to unload the mold.
https://www.kingbending.com/products/pipe-bender.html
201911ld